All ZinAmp modules can be purchased for use in your own project. Whether you require a regulated power supply, power-amplifier or speaker protection, our extensive range of modules can augment your existing project.
PCB mounted rotary switch with six positions. Switch has a splined shaft - suitable for ZinAmp models in black anodise finish where splined dials are used. Can be used in your own applications also. PCB and rotary switch are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. See datasheet for details
PCB mounted rotary switch with six positions. Switch has a round shaft - suitable for ZinAmp models in silver anodise finish where splined dials are used. Can be used in your own applications also. PCB and rotary-switch are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. See datasheet for details
PCB mounted 2 pole 2 position switch. Connects to the selector switch module via two stereo connections (left & right). Used to override the the selected input on the selctor switch with the record input whilst the line out is still the selected input - creating a record monitor loop. PCB and switch are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. See datasheet for details
PCB mounted 2 pole 2 position switch. Used to toggle the ZinAmp pre-amp EQ from Flat to Dynamic. PCB and switch are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. See datasheet for details
A PCB and a pair of 2 pole 2 position switches, 18.25mm apart. Used to switch 2 stereo pairs of speakers on and off. Includes connections for two optional 2ohm metal-clad resistors that are in-circuit only when both pairs of speakers are on. If you connect 2 pairs of 4ohm speakers and switch both on, the load is 2ohms; the 2ohm clad resistor ensures the amplifier sees 4ohms. PCB and switches are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. Clad resistors are not included. See datasheet for details
A PCB with two linear pots mounted 60mm apart. The combined effect of both pots is a logarithmic volume control where the pot on the left controls volume and the pot on the right controls the sensitivity or 'aggressiveness' of the volume control. Max and min impedences are described in the datasheet. PCB and pots are sold together and require soldering onto the PCB by the constructor with some additional resistors. Connectors and resistors need to be purchased separately and soldered on. See datasheet for details
A PCB with two linear pots mounted 120mm apart. This module is intended for use with a ZinAmp BiAmping amplifier, where separate gain controls for low and high frequencies are required. Can also be used for separate left and right channel volume controls in a custom installation. Note the pots supplied with this module are linear, but are made logarithmic by the addition of two pairs of 100k resistors. PCB and pots are sold together and require soldering onto the PCB by the constructor. Connectors and resistors need to be purchased separately and soldered on. See datasheet for details
A PCB with a single linear pot. This module is intended for use with a ZinAmp Power amplifier, where a single gain/voume control is sufficient. Note the pot supplied with this module is linear, but is made logarithmic by the addition of an optional pair of 100k resistors. PCB and pot are sold together and require soldering onto the PCB by the constructor. Connectors and resistors need to be purchased separately and soldered on. See datasheet for details
PCB mounted 2 pole 3 position switch. Used to switch on the amplifier and mute/unmute the amplifier. Position 1 is Off, 2 is On & Muted, 3 is On & Unmuted. Switching off always mutes first, prevening snap or thump in the speakers. This switch is exlusively for use with ZinAmp valve amplifiers where a timer module is fitted. PCB and switch are sold together and require soldering onto the PCB by the constructor. Connectors need to be purchased separately and soldered on. See datasheet for details
